This angle cross is usually used on a handrail on a staircase or other descent, joining the midrail to the intermediate posts. It is adjustable between 30-45° to allow for varying degrees of incline.

The 130 Adjustable Cross, as with all of Ezi Klamp’s products, is of high quality. It is available in sizes 2-4.

It is kept in good stock at our base in Bristol and can be delivered promptly to ensure there are no delays to your project.

The 131 Wall Flange is used when positional fixing is required, usually where a handrail, guard rail or other structure meets a wall on a level site. Four pre-drilled holes ensure the fitting is secure and effective.

This fitting is available in 5 different sizes and should not be used as a base plate to support a structure – the 132 Base Plate should be used instead.

Our warehouse in Bristol always has excellent stock of all products ready to ship out quickly and efficiently to ensure your project runs smoothly.

The key clamp 131-3 Wall Flange is used where positional fixing is required, typically used where rail meets a wall. Please note that this fitting is not designed for use as a base plate to support a handrail, guardrail or other structure – the 132-4 Base Plate should be used instead.

This fitting is designed for use as a base flange, to fix down vertical posts in a handrail or guard rail. The fixing holes are wide enough to ensure good chemical or mechanical fixing, and the two grubscrews in the upright socket provide greater stability.

The 132 Base Plate, available in 5 different sizes, should be fitted so that the fixing holes are in line with the applied load.

Our helpful team at Ezi Klamp will make sure you receive your order quickly so that your project can continue to run easily and efficiently.

The 132-4 Base Plate is one method for fixing the handrail, this is used when fitting posts to a flat surface. There are other methods for fixing post also.

This fitting is a plastic plug in grey to be fitted on open ended tube. It can be used to avoid finger snags on exposed tubing.

It is available in 5 different sizes and can be used with our high-quality tubing to ensure a neat fit is accomplished.

The 133 End Cap is always in stock at our warehouse in Bristol, so it can be delivered to you quickly, allowing your project to run smoothly.

This key clamp fitting is a ground socket for concreting in. It can be used effectively when handrail posts may need to be removable, as the setscrew allows the post to be removed when and if required.

The 134 Ground Socket is available in sizes 2-4, allowing you to choose the optimum size for your project.

This fitting is always kept in stock and available at our warehouse in Bristol, and out team of experts there will help to fulfil your order as quickly and efficiently as possible.

The 135 Clamp-On Tee is a 90° tee which performs the same function as the 101 Short Tee. However, due to its open socket, it can be added onto a complete structure, rendering it very useful when making additions or alterations to existing structures.

This tee is available in sizes 1-5 and is a great option for making changes to a project easily.

As with all of our products, this fitting is always kept in stock at Ezi Klamp, and can be delivered quickly to help your project.

The 137 Hinged Crossover fitting is perfect for any projects where new handrail needs to be added to an existing structure. It is most often used to clamp over an unremovable section of rail.

This fitting is available in size 4, and is kept in stock at our Bristol warehouse for speedy despatch so that your project can run smoothly and without delay.

This key clamp fitting secures around an upright post and works in conjunction with the 140 Gate Pin to form a complete gate hinge.

The 138 Gate Eye is available for sizes 1-4.

As with all our fixtures and fittings, this product is always in stock at our Bristol warehouse, and our team of experts will be happy to fulfil your order quickly so that your project runs smoothly.

The 140 Gate Pin is used with the 138 Gate Eye key clamp, also securing around the upright post to complete the gate hinge.

This key clamp fitting is available in sizes 1-4.

This fitting is always kept in good supply in our warehouse in Bristol, meaning that they are readily available to send out quickly so that your project can progress rapidly.

This bracket is often used to carry a handrail parallel to a wall, or sometimes down a decline where the terrain is unsuitable for floor mounted rails. It is used when positional fixing is needed, or to attach kickplates to upright posts.

The 143 Handrail Wall Bracket is reliable and strong and is available in sizes 2-4.

Ezi Klamp keeps stock of this bracket in at our Bristol warehouse, and your order can be delivered faster than our rivals to give your project no delays.

This key clamp fitting is designed to fix vertical handrails or guardrails to walls, ramps and steps. Access to the top fixing hole is limited, and this may restrict the length and type of fitting that can be used.

This fitting is available in sizes 2-4, and the tube cannot pass through the bottom of the socket. However, if the tube is required to do so, the base can be bored out for a surcharge.

Our team at the warehouse in Bristol will be happy to help you with your requirements and fulfil your order as fast as you need.

The 145 Side Support key clamp fitting is designed for side fixing handrails or guardrails to walls, ramps or steps.

Usually, the tube cannot pass through the bottom of the socket, but if this is a requirement, our team of experts can bore out the base for a small surcharge. This product is available in sizes 2-4.

This product is always kept in good supply at our warehouse in Bristol so that we can deliver your order promptly.

This is a palm-type fitting, usually used to fix handrails or guard rails to walls, ramps and steps. Usually, the tube cannot pass through the bottom of the socket, but if this is a requirement, our experts can bore out the base for a surcharge. The flush design of the fitting allows it to fit in closely to the structure.

This key clamp fitting comes in sizes 2-4 to suit your needs.

The 146 Palm Fixing is kept in stock at our warehouse in Bristol, meaning it is available and ready to be delivered to you quickly so that your project is kept on track.

The 146-4 Palm Fixing is a fitting which enables the post to be fixed to the side of a wall.

This tee is an offset swivel fitting, which can accommodate varying angles, making it versatile, an excellent benefit to your project. It is often used on ramps, staircases or other declines where the gradient angle is unknown, or where a handrail needs to be offset from the upright posts.

This product is a strong, reliable fitting, like all of our range, and is available in sizes 1-5.

The 147 Offset Swivel Tee is always kept in stock at our warehouse in Bristol and can be delivered to you faster than our rivals to give your project the best chance of success.

This combination of clamps is used together to create a variable angle corner joint with an angle range of 85° to 253°. They are typically used on handrails or guardrails to create a corner at something different than 90° with an upright post.

The fitting is priced and sold in pairs and is available in 5 different sizes.

A good stock is kept at our warehouse in Bristol, and we can deliver faster than our rivals to ensure your project gets ahead.

This simple key clamp fitting is designed for connecting two lengths of tube of the same diameter safely and securely. If a flusher finish is required, the 150 Internal Joint is an excellent alternative.

This fitting is available in sizes 2-4, all of which are kept in good stock at our warehouse in Bristol. Here, our team of experts will pick, pack and dispatch your order faster than our rivals to ensure that your project continues to run smoothly.

The 150 Internal Joiner is an alternative to the 149 External Joiner key clamp, designed to join two lengths of tube of the same diameter. It offers a smoother, more discrete finish if needed.

This fitting is available in sizes 1-5. It is not recommended to use this fitting as a load bearing point.

A good stock of this product is kept at out warehouse in Bristol and can be delivered fast so that your project remains on track.

The 150-3 key clamp fitting is a straight internal joiner for connecting two tubes of the same diameter. Can only be used with the standard 3.2mm wall thickness tube we supply. It is a required fitting for meeting DDA handrail requirements. 2 X DDA rings are required with each fitting to make a smooth, comfortable joint.

This is a key clamp that is used to connect four horizontal tubes at 90° angles, with a vertical upright going through the middle of the fitting. It is usually used as a midrail joint for a handrail or other structure but can also be used on the top rail with the centre post being capped.

The 158 6-Way Cross fitting is very useful for structures with multiple vertical posts and comes in sizes 1-5 to allow you to choose the perfect size for your project.

This key clamp fitting is always kept in stock in our warehouse in Bristol, and our team of experts there will makes sure the products you order are delivered promptly.

The 160 Clamp-On Crossover fitting is usually used to add to existing structures. It forms a 90° joint between tubes in a handrail, guardrail or other structure and is usually used to retro-fit a horizontal tube to the existing structure.

This key clamp is useful when dismantling an existing construction is impossible as it allows you to make alterations rather than having to build new structures. It is available in sizes 1-5.

The team at our warehouse in Bristol will be happy to pack and dispatch your order as quickly as they can so that your project can progress with all due haste.

This key clamp is designed to form a 90° offset crossover connection between two tubes. It is often used for racking systems, offset handrails and can help to reduce the needs for cutting tubes.

The 161 Crossover fitting comes in sizes 1-5 and are best used along with our own tubing for a polished finish.

Our warehouse in Bristol is well stocked up with this fitting, and our helpful friendly team of experts will be happy to prepare your order and make sure it is delivered on time so you can continue your project.